Ad Code

Ticker

6/recent/ticker-posts

Installation of OFC Ducts by Trenchless Techniques-HDD

Posted By: technopediasite


Image result for image of hdd HDPE installations
Installation of OFC Ducts by Trenchless Techniques By HDD

➤ The ducts in the intra-city fibre routes (including such inter-city routes that are common with intra-city routes) shall be installed by Horizontal Directional Drilling method unless approved by the Company in writing for installation by other methods.

 The Contractor shall mobilize equipment suitable to install the ducts up to required / specified depth below ground in all types of soils.

 All concerned authorities (water, oil and gas pipeline operators, telecom operators, power companies etc.) who may have their underground utilities in the area shall be informed well in advance and as built drawings obtained to ensure proper planning of HDD operation and drilling profile.

 Cross pits shall be made across approved duct alignment to verify information about existing underground utilities/facilities as provided by authorities having jurisdiction over the area and also to ascertain type of soil for safe working of HDD equipment.

Duct Installation Specifications

 Unless specified and /or agreed in writing by Company, the duct for intra-city networks shall be installed at a specified depth below ground except at entry and exit areas. The minimum depth at entry and exit pits shall be 1.2m for intra-city networks.

 The installation of ducts by HDD along inter-city routes (except those in common with intra-city routes) shall be at the same depth as specified for inter-city ducts installation by open-cut (i.e. 1.65m) or as per requirements of the authorities(e.g. in case of NH/SH/Railway/canal crossing etc.).

 Entry and exit pits shall be dug at both ends of the segment which shall later on become either a location for man-hole/hand-hole in case of intra-city routes or for installing duct couplers in case of inter-city routes. For inter-city routes MH/HH locations shall be as per issued for construction drawings only.

 The drilled hole profile between entry and exit pits (except transition areas) shall be as straight as possible. The final HDD profile shall become part of as-built documents.
Image result for image of hdd HDPE installations
 The hole made by HDD equipment shall be of adequate diameter to allow pulling all the ducts in one go as a bundle. The ducts in the bundle shall be properly bundled using suitable spacers and tied together during pulling. The capacity of pulling equipment shall be at least 1.5 times of theoretical calculated pull force.

 The Contractor shall submit a detailed HDD procedure for review/approval of Company. The procedure shall include at least following information:

(A)  Proposed locations, size and depth of entry and exit pits.
(B)  Proposed number of holes, hole diameter and hole profile for pulling HDPE duct(s).
(C)  Proposed HDD machine details along with drilling direction control/steering system                details.
(D)  Pulling load calculations and details of pulling equipment (pull head, winch, rope, etc.).
(E)  Method of safe disposal of bentonite slurry.
(F)  Follow the drawing provided the company.

 Upon obtaining approval of procedure, the Contractor shall prepare site by marking route and digging entry/exit pits at predetermined locations and drill the hole of required size for pulling the ducts through. Once the hole is ready, required number of ducts, already de-coiled and spread on the ground, shall be connected to a pulling head and pulled through the hole. Suitable swivel joint shall be used during pulling to prevent twisting of ducts during pulling.

 The drilling machine and pulling equipment shall be removed and moved to new locations. The pits shall be replaced with man-hole/hand-hole for termination of ducts and later blowing of cable and remaining area backfilled and restored to a conditions agreed to with the authorities having jurisdiction over the area. Bentonite slurry, if used, shall be recovered from the pits and disposed-off in a safe and environmental friendly manner and at locations approved by Authorities.

 The Contractor may have to deploy more than one set of HDD equipment to achieve required lay rate demanded by contract schedule.

  HDD shot must be HH to HH or MH/MH. Don't use couplers between the water/rail/culvert etc. crossing.

  HDD shot not considerable less than 100 Mtr. if crossing is upto 150-200mtr.


Post a Comment

14 Comments

  1. Your article contains very much information about the Trenchless. Your article is very informative and nicely describes the trenchless techniques of OFC ducts installation. Thanks for sharing this article here. trenchless raleigh

    ReplyDelete
  2. I generally check this kind of article and I found your article which is related to my interest. Genuinely it is good and instructive information.https://www.innovextechnologies.co.uk/. Thankful to you for sharing an article like this.

    ReplyDelete
  3. This post is so useful and valuable to increase our knowledge. I am happy that you have shared great info with us.pipe handler equipment online USA. Grateful to you for sharing an article like this.

    ReplyDelete
  4. I generally check this kind of article and I found your article which is related to my interest. Genuinely, it is good and instructive information about construction work. Thanks for sharing an amazing article here. Undercarriage Dozer Parts online

    ReplyDelete
  5. I am attracted by the presentation of this article. This information about Plumber Wheelers hill.is really good. I really appreciate your work. It is a gainful article for us. Keep posting. Thank you.

    ReplyDelete
  6. WIAPS Approved Contractor Barrow I liked your work and the way in which you have shared this article here about WIAPS Approved Contractor Barrow. It is a beneficial and helpful article for us. Thanks for sharing an article like this.

    ReplyDelete
  7. You have a genuine capacity to compose a substance that is useful for us. You have shared an amazing post about residential Building Designers Melbourne.Much obliged to you for your endeavors in sharing such information with us.

    ReplyDelete
  8. You have a genuine capacity to compose a substance that is useful for us. You have shared an amazing post about steinservicesupply.Much obliged to you for your endeavors in sharing such information with us.

    ReplyDelete
  9. You have a genuine capacity to compose a substance that is useful for us. Much obliged to you for your endeavors in sharing such online journals to us.Exterior home services Palatine

    ReplyDelete
  10. You are providing good knowledge. It is really helpful and factual information for us and everyone to increase knowledge. Continue sharing your data. Thank you. Read more info about Best Plumbing services

    ReplyDelete
  11. Excellent knowledge, You are providing important knowledge. It is really helpful and factual information for us and everyone to increase knowledge. Continue sharing your data. Thank you. Read more info about Home additions and renovations in Scarsdale NY

    ReplyDelete
  12. This article provided me with a wealth of information about heavy duty electric chain pulley. The article is incredibly helpful and offers some of the most useful information. Thank you for sharing it with us.

    ReplyDelete
  13. I am impressed with how nicely you described this subject, It is a gainful article for us. I found decent information in your article about handyman in mayfair london. Thanks for sharing it.

    ReplyDelete